国产又色又爽又高潮免费视频麻豆,国产三级精品三级在专区,日本丶国产丶欧美色综合 ,上司人妻互换hd无码

HomeHotlineContact
0position:Home>>News

Analysis of the reasons for the creeping and vibration of the edge milling machine

source:   author: time:2020-08-15 Visits:2216
There are many obvious abnormal phenomena in the milling machine, but in some economic CNC systems, there is no alarm. Even if there is an alarm sometimes, the alarm information shows that it is not the alarm of abnormal phenomenon you see. The creeping and vibration of the milling machine is an obvious example. When the milling machine runs at a low speed, the worktable of the CNC milling machine moves forward in a creeping manner; when the milling machine runs at a high speed, there will be vibration.

Because of the bad lubrication, the friction resistance increases when the milling machine table moves. When the motor is driven, the table does not move forward, which makes the ball screw produce elastic deformation and stores the energy of the motor on the deformation. When the motor continues to drive and the elastic force produced by the stored energy is greater than the static friction force, the milling machine table creeps forward and moves in this way again and again, resulting in crawling phenomenon.

Because the vibration frequency is proportional to the speed of the motor, the first thing to do is to check whether there is a fault in the motor, check the surface condition of the carbon brush and commutator, as well as the mechanical vibration, and check the lubrication of the ball bearing. The whole inspection does not need to be disassembled completely, but can be observed by the inspector. The bearing can listen to the sound with ears To check. If there is no problem, check the tachogenerator. The tachogenerator is usually DC.

A closed loop system may also cause system oscillation due to poor parameter setting. However, the best way to eliminate this oscillation is to reduce its magnification, to adjust RV1 and reverse clock direction in the FANUC system. At this time it can be seen that it will become better immediately. However, because of the relatively small range of RV1 regulating potentiometers, sometimes it can not be adjusted, it can only change the short circuited bar. Cut off the feedback resistance and reduce the magnification of the whole regulator.

More edge milling machines, with pressure beam milling machine, no pressure beam edge milling machine, end face milling machine, end face milling machine, planer. Please pay attention detroitnewsday.com


All rights reserved:WUXISHI XILI MILLING MACHINE CO.,LTD(detroitnewsday.com)  Su ICP 15043207-1 Design :25318.cn

狠狠躁天天躁夜夜躁婷婷| 99偷拍视频精品一区二区| 96在线看片免费视频国产| 亚洲国产成人精品无码区在线播放| 在线天堂免费观看.www| 成人免费一区二区三区视频软件| 成熟丰满熟妇高潮xxxxx| 亚洲AV无码一区二区三区DV| 国产精品久久久久久无码| а√天堂资源地址在线官网bt| 76少妇精品导航| 亚洲乱码日产精品bd在线观看| 国产特黄A三级三级三级| 国产片AV片永久免费观看| 久久久精品国产SM调教网站| 肉色超薄丝袜脚交一区二区| 国产在线拍揄自揄拍无码| 久久天天躁狠狠躁夜夜AV | 一卡2卡3卡4卡精品乱码视频| 精品人妻大屁股白浆无码| 学生妹亚洲一区二区| 亚洲 中文字幕 日韩 无码| 亚洲av日韩精品久久久久久| 国产又爽又黄无码无遮挡在线观看| 免费观看羞羞视频网站| 午夜一区欧美二区高清三区| 丰满熟妇人妻AV无码区| gogogo日本免费观看视频| 隔壁老王国产在线精品| 老司机午夜精品视频资源| 免费韩国性色生活片| 亚洲精品国产成人AV蜜臀| 精品人妻无码中字系列| 广东少妇大战黑人34厘米视频| 天堂网在线观看| 中文字字幕在线中文乱码| 年轻漂亮的人妻被公侵犯BD免费版| 亚洲AV永久无无码精品一区二区三区| 4hu四虎永久在线观看| 无码人妻丰满熟妇啪啪| 2022国产成人精品视频人|